Polycom
From CVL Wiki
(Difference between revisions)
| Line 44: | Line 44: | ||
IP: 128.173.89.184 | IP: 128.173.89.184 | ||
| − | 460 Durham | + | |
| − | Polycom | + | ==460 Durham Conference Room Directions== |
| − | + | *457 Whittemore Polycom Address: 128.173.90.254 | |
| + | |||
| + | ===Local Computer Content (No Polycom)=== | ||
| + | #Turn on '''Projector 1''' over conference table (Sharp remote) | ||
| + | #Change projector input to '''Computer 1''' (Sharp remote) | ||
| + | #Plug '''VGA INPUT''' cable into computer | ||
| + | #When finished, please change projector input back to '''HDMI''' and press '''Standby''' button | ||
| + | |||
| + | ===Polycom=== | ||
| + | ====Device Setup==== | ||
| + | #Turn on '''TV''' (Samsung Remote) | ||
| + | #* '''TV''' displays Polycom camera on video source '''HDMI2''' | ||
| + | #Turn on '''Projector 1''' over conference table (Sharp Remote) | ||
| + | #* '''Projector 1''' displays Polycom content on video source '''HDMI''' | ||
| + | #* '''Projector 1''' is also speaker source for room | ||
| + | #Turn on '''Polycom''' (Polycom remote) | ||
| + | #* Point remote at camera | ||
| + | #* Be patient, boot up takes a few minutes. | ||
| + | #* Polycom home screen is on '''TV''' or '''Projector 2''' | ||
| + | #'''Projector 2''' mirrors Polycom display on TV (no remote) | ||
| + | #* Projector 2 displays Polycom camera on video source HDMI | ||
| + | #If sending computer content, plug in '''POLYCOM CONTENT INPUT''' cable | ||
| + | |||
| + | ====Making a Call==== | ||
| + | #Press '''Home''' button | ||
| + | #Select '''Place a Call''' | ||
| + | #Enter the IP address and press '''Call''' button | ||
| + | #Remote site should answer automatically | ||
| + | |||
| + | ====Sending computer content==== | ||
| + | #Establish video call | ||
| + | #Plug '''POLYCOM CONTENT INPUT''' cable into computer | ||
| + | #Press '''Content''' button and select '''Computer''' | ||
| + | #* You should see content on Projector 1 | ||
| + | #Verify remote site can see content | ||
Revision as of 14:52, 20 March 2014
Contents |
457 Conference Room Directions
- 457 Whittemore Polycom Address: 128.173.90.254
Local Computer Content (No Polycom)
- Turn on Projector 1 over conference table (Sharp remote)
- Change projector input to Computer 1 (Sharp remote)
- Plug VGA INPUT cable into computer
- When finished, please change projector input back to HDMI and press Standby button
Polycom
Device Setup
- Turn on TV (Samsung Remote)
- TV displays Polycom camera on video source HDMI2
- Turn on Projector 1 over conference table (Sharp Remote)
- Projector 1 displays Polycom content on video source HDMI
- Projector 1 is also speaker source for room
- Turn on Polycom (Polycom remote)
- Point remote at camera
- Be patient, boot up takes a few minutes.
- Polycom home screen is on TV or Projector 2
- Projector 2 mirrors Polycom display on TV (no remote)
- Projector 2 displays Polycom camera on video source HDMI
- If sending computer content, plug in POLYCOM CONTENT INPUT cable
Making a Call
- Press Home button
- Select Place a Call
- Enter the IP address and press Call button
- Remote site should answer automatically
Sending computer content
- Establish video call
- Plug POLYCOM CONTENT INPUT cable into computer
- Press Content button and select Computer
- You should see content on Projector 1
- Verify remote site can see content
Audio Problems
Both the Polycom and Sharp projector have volume controls, please verify both are turned up
654 Whittemore
Polycom only
IP: 128.173.89.184
460 Durham Conference Room Directions
- 457 Whittemore Polycom Address: 128.173.90.254
Local Computer Content (No Polycom)
- Turn on Projector 1 over conference table (Sharp remote)
- Change projector input to Computer 1 (Sharp remote)
- Plug VGA INPUT cable into computer
- When finished, please change projector input back to HDMI and press Standby button
Polycom
Device Setup
- Turn on TV (Samsung Remote)
- TV displays Polycom camera on video source HDMI2
- Turn on Projector 1 over conference table (Sharp Remote)
- Projector 1 displays Polycom content on video source HDMI
- Projector 1 is also speaker source for room
- Turn on Polycom (Polycom remote)
- Point remote at camera
- Be patient, boot up takes a few minutes.
- Polycom home screen is on TV or Projector 2
- Projector 2 mirrors Polycom display on TV (no remote)
- Projector 2 displays Polycom camera on video source HDMI
- If sending computer content, plug in POLYCOM CONTENT INPUT cable
Making a Call
- Press Home button
- Select Place a Call
- Enter the IP address and press Call button
- Remote site should answer automatically
Sending computer content
- Establish video call
- Plug POLYCOM CONTENT INPUT cable into computer
- Press Content button and select Computer
- You should see content on Projector 1
- Verify remote site can see content
